Logo

C1221 Engine Trouble Code

C1221 Engine

When you check engine light came on code C1221 the reason should be . However your vehicle's manufacturer may have a different definition for the C1221 OBD-II Diagnostic Chassis (C) Trouble Code. So you should chech it on our car models.

Theoretically you can drive a few more days or even months with a broken MAF sensor in your car. You will notice a decrease in gas mileage/km and over time the car will at the end start stalling a lot from engine side. At a shop, the replacement cost is between $300-$450 depending on the car, but that's usually the cost of parts because the labor is relatively simple.

C1221 Code Meaning :

C
OBD-II Diagnostic Chassis (C) Trouble Code For Engine
1
Fuel And Air Metering
2
Ambient Air Temperature Sensor Circuit Low
2
Crankshaft Position Sensor A Circuit Malfunction
1
Glow Plug/Heater Circuit 'A' Malfunction

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

C1221 OBD-II Diagnostic Chassis (C) Trouble Code Description

C1221 engine trouble code is about Glow Plug/Heater Circuit 'A' Malfunction. Ambient Air Temperature Sensor Circuit Low and Crankshaft Position Sensor A Circuit Malfunction causes most of code C1221.

Reason For C1221 Code

The reason of C1221 OBD-II Engine Trouble Code is Ambient Air Temperature Sensor Circuit Low.

C1221 code on vehicles with electronically controlled automatic transmissions, the 3-4 shift solenoid is responsible for actuating the hydraulic circuits to activate clutches or bands that change gears inside the automatic transmission in your car.

How To Repair C1221 Code

Before starting let's see C1221 repairing process steps:

  • Qualified technicians will begin by using a scan tool to access C1221 code stored in the ECU.
  • Technicians will note C1221 code present and any freeze frame data associated with them.
  • After all, if you sure the engine trouble is finished, the code will be cleared.

All functions are tested, lights, gauges, central display and warning functions. Once the unit is identified as faulty, we then move onto the rebuild stage. Each unit is fully stripped, all common failing components are then replaced with versions that are higher rated than standard. Once the rebuild is complete, we then retest the instrument cluster to ensure it functions in accordance with the manufacturers original specification.

C1221 code is stored again, the mechanic will perform a visual inspection of the pressure control solenoid and related systems. If any circuits or connections are damaged or loose, they will resolve these issues and move on to retest the system.

Sometimes C1221 code comes with C122100 code.

Diagnosis Of Engine Error OBD Code C1221

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a C1221 trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the C1221 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.

The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.

All Engine Trouble Codes

All engine trouble codes with P, U, B and C engine codes.

Code Search

Please fill the "Code Box" to find engine fault code.

Example: 0140

Car Models :

Please select your car.

How To Read Engine Codes ?

Ways to read engine trouble codes.

How To Clear Check Engine Lights ?

Ways to clear check engine light on car panel.

Check Engine Light Dictionary

Ways to clear check engine light on car panel.